Volt Solar Panel

Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar

Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar
Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar
Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar

Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar

10,000 WATT CHARGE CONTROLLER WITH. 3 PHASE BRAKE SWITCH, RECTIFIER. And Digital LED display for battery voltage.

You can connect both wind and solar at the same time! COMBO 440 amp CHARGE CONTROLLER. 3 PHASE OUTPUT WIND TURBINES. IT CAN DISCONNECT THE INCOMING POWER OR DIVERT IT. Use for 3 phase ac output wind turbines.

Designed, assembled, and quality checked in the USA using global parts. Comes with 5 feet of heavy duty cables. Comes completely pre-wired as shown above. Charge controller with 600 watt divert load, 3 phase 50 amp. Brake switch and 90 amp 1000 volt rectifier.

Digital Led display that shows battery voltage. (does not come with battery). For 12 volt systems ONLY. Comes prewired for plug and play with. Charge controller with LED volt meter.

Heavy duty battery cables and rectifier for 3-phase output wind turbine connection. You can also attach additional DC wind turbines and solar panels to the board. Some of the key features of this hybrid controller are. Dual microprocessor controlled for stability and accuracy. Multiple user changeable settings and trip points for many various system requirements and applications.

You can change the dump point voltage level, end of dump voltage level, and length of time in divert mode when end dump point voltage is reached (between 0 to 999 seconds, or 0 to 999 minutes) The controller will also monitor the diversion/disconnect activity and increase it's duration several times when your batteries are full. This feature is also adjustable. Isolated Electronics Protection - Almost impossible to accidentally connect wind or solar directly to the circuit board.

On board relay isolates electronics from back voltage spikes from large 440 amp relay. This is important to get the longest life out of the electronics. No one else has this!

Can be operated at 100% duty cycle conducting. Loads up to 440 amps or 10,000 watts. Please note that the normally closed contacts can handle 100 amps continuous duty. Battery Status LED lets you know your battery's actual voltage!

Green LED on board lets you know the controller is in dump mode. Plug & Play: Long leads for easy termination to your 12 volt battery or battery bank. Can divert the charging source from the batteries to the load or dump both the batteries along with the charging source.

Connect both wind and solar at the same time. Ultra low power consumption, even with the volt meter on (almost negligible). The volt meter can be set to turn off after periods of inactivity. Comes completely prewired as shown above.

Mounting Plate Dimensions: 12 inches x 12 inches. Be wary of cheap, less capable knock-offs of our model controller that are too basic to properly charge a battery. They will attempt to only turn ON and OFF for the SAME length of time, every time, when your battery is full.

This will constantly boil your battery when it is full or not properly fill it or both. An improperly charged battery will have a short life and cannot be brought back. One to two years instead of 10 years or more of life!

You don't benefit from returning a product after it ruins your system. A charge controller must operate a relay whether mechanical or solid state(SSRs).

The relay turns the charging from your solar, wind, or hydro ON or OFF to your batteries. If you have 100 amps of solar charging being turned ON and OFF to your batteries you NEED to vary the time between the ON/OFF cycles. Our controller has custom programming that cannot be duplicated by Dime Store sellers and is, of course, user changeable.

Ours will more slowly top-off your battery! It will do this by adjusting itself every time your battery is full by increasing the duration of the next OFF cycle by up to 4 increased OFF times. For example: 5 seconds to 10, then 10 to 20, then 20 to 40 and will maintain a 40 second OFF time.

You can adjust the starting 5 seconds down to 1 or up to 999. We even went a step further and programmed in a "sweep time" which is a secondary sensing timer that starts directly following an ON cycle. This tells the controller that it has or has not been too long before battery charging is needed again.

The user adjustable sweep time allows the user and controller to have a wide range of charging times on any size battery bank. We also pre-wire and pre-program ours for you to be able to get up and going without becoming an expert. You're taking a risk with your system if accepting a too-good-to-be-true price or product description.

If you're not convinced this is the controller for you, please check our other charge controllers or ask us which one is right for you. Products may be slightly different than the ones pictured. If our supplier runs short of the products shown, we will substitute them for the same quality or better.

Damage from marine use and/or saltwater environments. Corrosion due to saltwater air. The item "Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar" is in sale since Friday, March 27, 2015. This item is in the category "Home & Garden\Home Improvement\Electrical & Solar\Alternative & Solar Energy\Wind Generators". The seller is "mountainwindtradingco" and is located in Mansfield, Missouri. This item can be shipped worldwide.

  • Voltage: 12 V
  • EAN: Does not apply
  • Modified Item: No
  • Custom Bundle: No
  • ISBN: Does not apply
  • UPC: Does not apply
  • MPN: 3pall_in_one_DIG_12V
  • Brand: SM
  • Non-Domestic Product: No


Charge Controller 12 volt DIG with 3 Phase Brake Switch 4 Wind Turbine & Solar